The Lynk & Co 01 may wear a Chinese badge, but beneath the skin it shares a platform — and a key architecture — with the Volvo XC40. Xhorse has now confirmed that the Xhorse VVDI Key Tool Plus can program a spare smart key for the 2022 Lynk & Co 01 by reading the vehicle's Central Electronic Module (CEM) exactly the way a Volvo technician would. For locksmiths and independent shops already cutting Volvo keys, that means a brand-new vehicle family opens up at almost no extra cost.

Why the Lynk & Co 01 Shares Its Key DNA with Volvo
Lynk & Co is the brand born from the Geely–Volvo Cars partnership, and the 01 crossover is built on the Compact Modular Architecture (CMA) — the same platform that underpins the Volvo XC40. That shared DNA runs deeper than the chassis: the vehicle's immobilizer and key-management logic live in a Central Electronic Module (CEM) that behaves like its Swedish sibling.
This is precisely why Xhorse routes the Lynk & Co 01 through the Volvo menu in the VVDI Key Tool Plus. Instead of building a dedicated Lynk & Co profile, the tool reads the CEM directly and treats the car as an XC40. For a technician, that is the single most important detail of the job: select Volvo → XC40 → 2021 → Smart Key System, and the rest follows the familiar Volvo workflow.
That matters commercially, too. Lynk & Co has been expanding steadily across Europe and Asia, and independent shops are increasingly seeing 01, 02, 03, and 05 models roll into their bays with the same all-keys-lost and spare-key jobs they already handle for Volvo. A technician who knows the XC40 procedure can take on Lynk & Co work with no additional training and no new hardware.

What the CEM Read Actually Involves
The heart of the job is reading the CEM, which houses the NXP MPC5747G microcontroller that stores the vehicle's key and immobilizer data. On the 01, the CEM is located near the driver's pedals, tucked behind the lower dash area.

The key programmer connects to the CEM in-circuit and reads it using a 100-ohm resistor in the harness — a well-established trick for pulling a clean read from the MPC5747G without desoldering the chip. The resistor stabilizes the signal path on the module's data line, letting the tool extract the data it needs to authenticate and learn a new key.
Once the CEM read completes, the tool generates the key-learning data, and the technician programs a new XM38 universal smart key against the vehicle. The key blade is cut from blank #38, and the remote functions are learned as part of the same procedure.
Step-by-Step: Programming the Spare Key
Step 1: Access the CEM
Locate the CEM near the driver's pedals and remove the lower trim panel to expose the module and its harness connector.
Step 2: Read the CEM
Connect the VVDI Key Tool Plus to the CEM with the 100-ohm resistor in line on the appropriate data pin. On the tool, navigate to IMMO Programming → Volvo → XC40 → 2021 → Smart Key System, then run the CEM read.
Step 3: Cut and Prepare the Key
Cut the blade from key blank #38 and pair it with an XM38 universal smart key remote. Fit the blade to the remote before programming.
Step 4: Program and Verify
Follow the tool's on-screen prompts to learn the new smart key remote, then verify lock, unlock, and start functions before handing the vehicle back.

What Technicians Should Know Before Starting
A few shop-floor notes matter here. First, treat the 01 as a Volvo XC40 throughout the process — that menu routing is deliberate, not a workaround. Second, the 100-ohm resistor is load-bearing: an unstable read can fail the key-learning step or produce an incomplete dump, so confirm the resistor value and the connection before reading. Third, verify the exact model year and Smart Key System variant before selecting the menu path, since later model years may differ.
For shops that already stock Xhorse key-programming hardware, the Lynk & Co 01 is effectively a no-new-tooling add-on. The VVDI Key Tool Plus is the same device many technicians already use for Volvo, BMW, and Toyota keys, so adding Lynk & Co coverage costs nothing beyond the key blank and a few minutes of bench time — and it future-proofs the shop for a Chinese-brand fleet that is only growing across Europe and Asia.
The broader takeaway is worth keeping in mind: as Chinese automakers keep shipping new platforms overseas, their immobilizer and key systems are increasingly reusing supplier and platform DNA from European brands. Reading the module directly — rather than waiting for a brand-specific menu to appear — is becoming the faster, more reliable path for independent key programmers. The Lynk & Co 01 is a clean early example of that shift.
Written by Roberto Vargas, Key Programming & ECU Specialist at vxdas.com