The Hyundai and Kia 4A transponder has been one of the harder chips in the locksmith world to duplicate. Autel's latest KM100 software update changes that, adding 4A transponder cloning so a working Hitag AES ID4A smart key can be copied onto the AT100 super chip in a matter of minutes, without a full key-learning session.

Why the 4A Chip Gave Locksmiths Trouble
Most older transponders are relatively simple to copy. The chip stores a fixed identifier, a cloning tool reads it, and the value is written onto a blank chip. The Hyundai and Kia 4A system does not work that way. It is a Hitag AES transponder — the ID4A smart key — that uses AES encryption and mutual authentication with the vehicle's immobilizer.
That means the chip does not simply broadcast a static code. It runs a cryptographic exchange, and the vehicle challenges the key every time the ignition is turned on. For years, the only reliable path to a second key was a full key-learning procedure: read the vehicle's PIN, enter immobilizer programming, and register the new key through the car's system. That is slower, requires server-side PIN calculation on many models, and can be intimidating for a shop that is still building out its key business.
Cloning removes that friction. Instead of registering a new key with the car, the tool copies the identity of an existing, authorized key onto a blank. The vehicle never knows a second key was made — it simply sees the same key twice. For a customer who has one working smart key and wants a spare, that is often exactly the right job.
The KM100 4A Cloning Flow, Step by Step
The new routine lives inside the KM100's Clone menu. The technician starts by selecting 4A Transponder Cloning, then reads the original key's information. The KM100 identifies it as a Hitag AES ID4A smart key and prepares to capture the data it needs.
Next comes the acquisition step, which is where the procedure differs from older chip cloning. The KM100 is placed close to the ignition coil while the original key is used to turn the ignition on. For a smart key, the battery is removed first so the remote's passive transponder signal can be read cleanly. The ignition is cycled on and off until the tool confirms it has acquired enough data.

Once the data is captured, the original key is placed back in the KM100's key slot for authentication. The tool calculates the immobilizer secret key and PIN code, then reads the original key's information one more time. With that complete, the original key is removed and a blank AT100 super chip is dropped into the KM100 coil. The tool writes the captured identity to the AT100, and the clone is finished.
The result is a chip that can be used for emergency starting — a spare that behaves like the original key in the ignition. The whole routine takes minutes rather than the longer, multi-step process of full immobilizer programming.
Cloning vs. Key Learning: When Each Makes Sense
Cloning is not a replacement for full key learning; it is a different tool for a different job. Cloning shines when a customer still holds a working key and simply wants a backup. There is no change to the vehicle's stored key count, no immobilizer re-sync, and no risk of leaving the car in a learned state that locks out other keys. It is also useful for all-keys-lost emergencies where the goal is to get a drivable vehicle back on the road quickly before a more complete solution is arranged.
Full key learning remains the right choice when a key has been lost outright, when a customer wants the old key permanently removed from the vehicle's memory, or when the job calls for programming a brand-new remote into the system rather than duplicating an existing one. Shops that offer both — key programming tools for learning and cloneable transponder chips for duplication — can cover nearly every key job that walks through the door.

What You Need on the Bench
The capability centers on two pieces. The first is the KM100 itself, Autel's key-generation tool that now carries the 4A cloning routine after the latest update. The second is the AT100 super chip, Autel's universal transponder blank designed to accept a cloned identity. Keep a stock of AT100 blanks on hand so a clone job is never delayed waiting for parts.
For shops looking to build this out as a service, the surrounding tooling matters. A full Autel diagnostic and key-programming setup lets the same bench handle the read-the-PIN, learn-the-key jobs alongside cloning, and a set of remote keys and shells covers the mechanical half of delivering a finished spare key to the customer.
It is also worth remembering that the 4A system spans a broad slice of the Hyundai and Kia lineup, so a single workflow learned once repeats across many models. Technicians should still verify exact vehicle coverage against Autel's supported list before quoting, as software versions and regional variants can shift what a given device supports on a given day.

What to Watch Before You Quote a Job
A few best practices keep a clone job clean. Always confirm the original key is genuinely working before starting — cloning only copies what is already there. For smart keys, follow the battery-removal step carefully so the passive signal reads cleanly and the authentication does not time out. And as with any key work, make sure the customer can demonstrate ownership of the vehicle before duplicating a key.
The broader point is that key duplication keeps getting easier as chip technology advances, and the tools that once lagged behind the OEMs are catching up fast. Autel closing the 4A cloning gap is one more sign that a well-equipped independent locksmith can now handle the majority of modern transponder jobs in-house, without sending customers to a dealer.
Written by Roberto Vargas, Key Programming and ECU Specialist at vxdas.com