KESS3 Upgrade 3.74 adds read and write protocols for the Hitachi ETC94-110N transmission control unit, in both OBD and BENCH modes. The release opens transmission work on a large installed base of rear-wheel-drive and all-wheel-drive Infiniti, Nissan and Renault vehicles built from 2009 onward, and extends the same capability to Powergate for remote reprogramming.

What the KESS3 3.74 Update Actually Covers
The update targets a single, widely used component: the Hitachi ETC94-110N TCU. This is the transmission control module fitted to the JATCO-derived seven-speed automatic used across Nissan's rear-drive platform. It is the brain behind shift strategy, torque-converter lockup, line pressure and shift-quality calibration on some of the highest-torque engines in the segment.
Alientech lists coverage spanning sports cars, premium saloons, SUVs and pick-ups. On the Infiniti side, that means EX, FX, G37, M30, M37, M56, Q40, Q50, Q60, Q70, QX50, QX56 and QX70. On the Nissan side, the 370Z and Fairlady Z, Armada, Frontier, NP300 Navara, Patrol, Skyline and Terra are included, alongside the Renault Alaskan. The common thread is torque: Nissan's 3.7-litre V6 and 5.6-litre V8, plus Renault's 2.3, 2.5 and 3.0 dCi diesels, all place heavy demand on the transmission controller.
Two connection paths are now supported. Technicians can read and write through the OBD port with the TCU still bolted in the car, or remove the module and work directly from the connector in BENCH mode. Powergate adds OBD-based remote programming, so a tuner can deliver a transmission calibration through the customer's own device without the vehicle ever entering the workshop.
Why Transmission Control Units Are the Next Tuning Frontier
For years, aftermarket tuning concentrated on the engine ECU. The transmission controller was often left stock, which created a mismatch: a recalibrated engine pushing more torque than the factory shift strategy was designed to handle. The result is harsh gear changes, early torque-converter lockup, and in the worst cases, transmission damage. Opening the TCU closes that loop.
Transmission faults are also a daily repair-shop reality, not a niche tuning concern. Worn valve bodies, failing shift solenoids and torque-converter shudder are common on high-mileage seven-speed autos. When a module is replaced or a valve body is rebuilt, the controller often needs to be reflashed or cloned to match the vehicle. OBD access turns what used to be a bench-only, module-out job into a diagnostic-port operation.

OBD vs BENCH: Choosing the Right Connection
The two modes serve different jobs, and the release lets the technician pick whichever fits the situation. OBD is the fast path for routine reads, calibration writes and remote Powergate jobs, because nothing has to be removed from the vehicle. It is the first choice for a vehicle that drives into the bay and needs a shift-quality adjustment or a stock-file backup.
BENCH mode is the fallback for vehicles where the OBD link is unavailable, interrupted, or where a module has already been pulled. With the TCU removed and powered on the bench, KESS3 talks directly to the controller connector. This is the safer route for recovery work, and for modules that are being prepared for installation in another vehicle. Having both options in one tool avoids the awkward situation of turning a customer away because a connection route failed.
For shops building out this service, the underlying tooling matters as much as the protocol. Transmission work pairs naturally with ECU and TCU tuning tools for calibration, and with transmission service tools for the mechanical side of a gearbox job.

What It Means for Tuning and Repair
The practical upside is speed and scope. A technician who previously had to remove, bench-read and refit a TCU can now perform the same read through the diagnostic port in a fraction of the time. For tuners working on boosted 370Z or Infiniti Q50 builds, the ability to rework shift points and torque limits alongside the engine map is a genuine capability upgrade rather than a convenience.
Remote delivery is the other piece that changes the economics. Powergate support means a transmission calibration can be sent to a customer's device and applied through OBD, expanding the tuner's reach beyond the local area. This mirrors the direction the wider industry is heading, where software and remote reprogramming services are becoming as important as the hardware in the bay.
There is also a parts angle worth noting. When a controller fails outright and cannot be recovered, a used or remanufactured unit often needs its data written to match the vehicle's immobilizer and engine calibration. That is where a replacement ECU and TCU module combined with proper read/write tooling keeps the job in-house instead of sending it to a dealer.

What to Expect Next
Alientech has been releasing KESS3 upgrades at a steady weekly cadence, and transmission controllers are a logical area for continued expansion. As hybrid and electrified drivetrains push more vehicles onto multi-speed and e-CVT-style transmissions, the number of TCU variants that independent shops encounter will only grow. Tools that can read and write those controllers through OBD, bench and remote channels are positioned to capture that work.
For shops and tuners already invested in the Alientech ecosystem, this update is available through the normal KESS3 software release channel and requires no additional hardware for the OBD path. Technicians should verify exact vehicle and engine coverage against the supported list before quoting a transmission job, and always back up the original TCU file before any write operation.
Written by Roberto Vargas, ECU and Transmission Tuning Specialist at vxdas.com