With superior systems diagnoses, this multipurpose obd2 scanner can be used to read all available systems’ ECU information to facilitate the vehicle diagnosis. The complete systems vary from different cars and they usually include Engine, transmission, ABS, SRS, SAS, TPMS, EPB and Fuel systems etc.

1. Read DTCs from the vehicle’s control systems to locate problem areas, and offer solutions;
2. Erase the codes easily after DTCs retrieving and certain repairs have been carried out;
3. Live data shows each parameter item displayed in analog, text, waveform graph modes etc.;
4. The active test used to access vehicle-specific subsystem and component tests.

1) Oil Reset
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

2) Elec.Throttle Adaption
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.

3) Steering Angle Reset
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering.

4) Battery Matching
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

5) ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

6) Break-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.

7) DPF Regeneration
DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.

8) Gear Learning
After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed.

9) IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

10) Injector Coding
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity.

11) TPMS Reset
Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions

12) Suspension Matching
This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.

13) AFS Reset
This feature is used to initialize the adaptive headlamp system.

14) A/T Learning
This function can complete the gearbox self-learning to improve gear shifting quality.

15) Sunroof Initialization
This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc.

16) EGR Adaption
This function is used to learn the EGR valve after it is cleaned or replaced.

17) Airbag Reset
This function resets the airbag data to clear the airbag collision fault indicator.

18) Transport Mode
ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal.

19) A/F Reset
This function is applied to set or learn Air/Fuel ratio parameters.

20) Stop/Start Reset
This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware).

21) NOx Sensor Reset
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu.

22) AdBlue Reset (Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

23) Seat Calibration
This function is applied to match the seats with memory function that are replaced and repaired.

24) Coolant Bleeding
Use this function to activate the electronic water pump before venting the cooling system.

25) Tyre Reset
This function is used to set the size parameters of the modified or replaced tire.

26) Windows Calibration
This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window.

27) Language Change
This function is used to change the system language of the vehicle central control panel.

Reading Codes
Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset
Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream
Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data
Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test
Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test
Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test
Certain vehicle components can be actuated by commands sent from the scanner to test their operability

--Ecu Coding and Active Test
(These two functions can buy directly at the "thinkcar store" in thinktool mini,49.95 dollars one brand one year each)

Active Test:
This thinktool mini full system obd2 scanner request information or command a module to perform specific tests and functions. For instance, in the case of OBD II generic information Mode 1, you can initiate a request for information from the powertrain control module, and the PCM responds by sending the information back to the scan tool for display.

English, French, German, Spanish, Italian, Portuguese, Japanese,Russian,Polish,Hungarian,Arabic,Greek,Slovak,Korean,Swedish,Dutch,Traditional Chinese

priter:support diagnostic report print service
worklight:offer lighting assistant service
video scope:allow technicians to check faults in narrow and dark space
modular dock:rechange for the table
thermal imager:scan and capture temperature
scope box:support diagnostic report print service
battery tester:support diagnostic report print service
Thinktpms G1:bring tpms service to your smartphone

note:need to buy these modulars seperately

Package list:

1x Thinktool mini
1x Bluetooth (Pre-installed in the Unit)
1x Charging Cable
1x Passport Envelope
1x User Manual

With superior systems diagnoses, this multipurpose obd2 scanner can be used to read all available systems’ ECU information to facilitate the vehicle diagnosis. The complete systems vary from different cars and they usually include Engine, transmission, ABS, SRS, SAS, TPMS, EPB and Fuel systems etc.

1. Read DTCs from the vehicle’s control systems to locate problem areas, and offer solutions;
2. Erase the codes easily after DTCs retrieving and certain repairs have been carried out;
3. Live data shows each parameter item displayed in analog, text, waveform graph modes etc.;
4. The active test used to access vehicle-specific subsystem and component tests.

1) Oil Reset
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

2) Elec.Throttle Adaption
Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.

3) Steering Angle Reset
To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering.

4) Battery Matching
This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

5) ABS Bleeding
When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

6) Break-pad Reset
lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.

7) DPF Regeneration
DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.

8) Gear Learning
After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed.

9) IMMO Service
To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

10) Injector Coding
Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity.

11) TPMS Reset
Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions

12) Suspension Matching
This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you need to perform thisfunction to adjust the body height sensor for level calibration.

13) AFS Reset
This feature is used to initialize the adaptive headlamp system.

14) A/T Learning
This function can complete the gearbox self-learning to improve gear shifting quality.

15) Sunroof Initialization
This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc.

16) EGR Adaption
This function is used to learn the EGR valve after it is cleaned or replaced.

17) Airbag Reset
This function resets the airbag data to clear the airbag collision fault indicator.

18) Transport Mode
ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal.

19) A/F Reset
This function is applied to set or learn Air/Fuel ratio parameters.

20) Stop/Start Reset
This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware).

21) NOx Sensor Reset
NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu.

22) AdBlue Reset (Diesel Engine Exhaust Gas Filter)
After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.

23) Seat Calibration
This function is applied to match the seats with memory function that are replaced and repaired.

24) Coolant Bleeding
Use this function to activate the electronic water pump before venting the cooling system.

25) Tyre Reset
This function is used to set the size parameters of the modified or replaced tire.

26) Windows Calibration
This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window.

27) Language Change
This function is used to change the system language of the vehicle central control panel.

Reading Codes
Show the detailed description of the Diagnostic Trouble Code (DTCs)

Erasing Codes & Reset
Turns off Check Engine Light (MIL), clears codes and resets monitors.

Data Stream
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

I/M Readiness Status
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

Read Live Data Stream
Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

View Freeze Frame Data
Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

O2 Sensor Test
Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

On-Board Monitor Test
Retrieves and displays test results for emission-related powertrain components and systems.

Read Vehicle Information
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

Component Test
Certain vehicle components can be actuated by commands sent from the scanner to test their operability

--Ecu Coding and Active Test
(These two functions can buy directly at the "thinkcar store" in thinktool mini,49.95 dollars one brand one year each)

Active Test:
This thinktool mini full system obd2 scanner request information or command a module to perform specific tests and functions. For instance, in the case of OBD II generic information Mode 1, you can initiate a request for information from the powertrain control module, and the PCM responds by sending the information back to the scan tool for display.

English, French, German, Spanish, Italian, Portuguese, Japanese,Russian,Polish,Hungarian,Arabic,Greek,Slovak,Korean,Swedish,Dutch,Traditional Chinese

priter:support diagnostic report print service
worklight:offer lighting assistant service
video scope:allow technicians to check faults in narrow and dark space
modular dock:rechange for the table
thermal imager:scan and capture temperature
scope box:support diagnostic report print service
battery tester:support diagnostic report print service
Thinktpms G1:bring tpms service to your smartphone

note:need to buy these modulars seperately

Package list:

1x Thinktool mini
1x Bluetooth (Pre-installed in the Unit)
1x Charging Cable
1x Passport Envelope
1x User Manual